What temperature should I print Matte PLA on the Elegoo Centauri Carbon?

Start at 210°C for the hotend and 60°C for the bed, then run a temperature tower across 195–220°C to dial in your exact filament brand.

What print speed works for Matte PLA on this printer?

Around 171 mm/s is a safe starting point on the Elegoo Centauri Carbon. It can go faster once the profile is tuned, but start conservative for clean walls.

What retraction should I use?

Use about 0.8 mm of retraction (direct drive needs very little). If you see stringing, raise retraction speed before distance and dry the filament.

Do I need an enclosure for Matte PLA on the Elegoo Centauri Carbon?

No, Matte PLA prints fine in the open on the Elegoo Centauri Carbon.

Home › Elegoo Centauri Carbon › Matte PLA

Matte PLA settings for the Elegoo Centauri Carbon

Great match

⚡ Quick answer: Print Matte PLA on the Elegoo Centauri Carbon at 210°C hotend, 60°C bed, 171 mm/s, 100% part-cooling fan and 0.8 mm retraction. Run a temperature tower to fine-tune your exact spool.

These are tuned starting settings for printing Matte PLA on the Elegoo Centauri Carbon. The Elegoo Centauri Carbon has a direct-drive extruder with an all-metal hotend, so we set the hotend to 210°C and the bed to 60°C. Matte PLA hides layer lines with a chalky finish and prints just like standard PLA.

210°C

Hotend

60°C

Bed

171 mm/s

Speed

100%

Part fan

Recommended Matte PLA profile

Hotend temperature	210°C (tower 195–220°C)
Bed temperature	60°C
Print speed	171 mm/s
Retraction	0.8 mm (direct drive)
Part cooling fan	100%
Bed adhesion	Easy; glue stick optional.
Nozzle	Brass 0.4 mm
Difficulty	Beginner

💡 Best uses for Matte PLA: display models and matte-finish parts.

Shop Matte PLA on Amazon →

Troubleshooting Matte PLA on the Elegoo Centauri Carbon

Problem	Fix
Stringing or fine hairs	Dry Matte PLA before printing, drop the hotend a few degrees below 210°C, and raise retraction toward 1.2 mm. Damp filament is the No. 1 cause of stringing.
Poor first-layer adhesion	Easy; glue stick optional. Re-level the bed, set a slightly squished first layer, and wipe the sheet with IPA so it is grease-free.
Blobs, zits or rough walls	Slow the outer wall, enable coasting/wipe, and keep retraction near 0.8 mm. If tops look rough, nudge the part-cooling fan higher.

FAQ

What temperature should I print Matte PLA on the Elegoo Centauri Carbon?: Start at 210°C for the hotend and 60°C for the bed, then run a temperature tower across 195–220°C to dial in your exact filament brand.
What print speed works for Matte PLA on this printer?: Around 171 mm/s is a safe starting point on the Elegoo Centauri Carbon. It can go faster once the profile is tuned, but start conservative for clean walls.
What retraction should I use?: Use about 0.8 mm of retraction (direct drive needs very little). If you see stringing, raise retraction speed before distance and dry the filament.
Do I need an enclosure for Matte PLA on the Elegoo Centauri Carbon?: No, Matte PLA prints fine in the open on the Elegoo Centauri Carbon.

Sources & how we tuned this

These settings are community-tested starting points, cross-checked against manufacturer guidance and trusted material references:

Last verified: 2026-07-17. Always run a temperature tower and a small calibration print for your exact spool.