What temperature should I print HIPS on the Creality Ender 3 S1?

Start at 240°C for the hotend and 100°C for the bed, then run a temperature tower across 230–255°C to dial in your exact filament brand.

What print speed works for HIPS on this printer?

Around 56 mm/s is a safe starting point on the Creality Ender 3 S1. It can go faster once the profile is tuned, but start conservative for clean walls.

What retraction should I use?

Use about 0.8 mm of retraction (direct drive needs very little). If you see stringing, raise retraction speed before distance and dry the filament.

Do I need an enclosure for HIPS on the Creality Ender 3 S1?

Yes — HIPS needs an enclosure to avoid warping, and the Creality Ender 3 S1 is open, so add one or expect warping and cracking on larger parts.

Home › Creality Ender 3 S1 › HIPS

HIPS settings for the Creality Ender 3 S1

Workable with mods

⚡ Quick answer: Print HIPS on the Creality Ender 3 S1 at 240°C hotend, 100°C bed, 56 mm/s, 0% part-cooling fan and 0.8 mm retraction. Run a temperature tower to fine-tune your exact spool.

These are tuned starting settings for printing HIPS on the Creality Ender 3 S1. The Creality Ender 3 S1 has a direct-drive extruder with a PTFE-lined hotend, so we set the hotend to 240°C and the bed to 100°C. HIPS doubles as a light structural material and a limonene-dissolvable support for ABS.

240°C

Hotend

100°C

Bed

56 mm/s

Speed

Part fan

⚠️ HIPS needs an enclosure and dissolves in limonene. The open Creality Ender 3 S1 works for small parts, but expect warping on anything large.

Recommended HIPS profile

Hotend temperature	240°C (tower 230–255°C)
Bed temperature	100°C
Print speed	56 mm/s
Retraction	0.8 mm (direct drive)
Part cooling fan	0%
Bed adhesion	ABS slurry or glue; enclosure needed.
Nozzle	Brass 0.4 mm
Difficulty	Advanced

💡 Best uses for HIPS: dissolvable support for ABS (limonene) and light parts.

Shop HIPS on Amazon →

Troubleshooting HIPS on the Creality Ender 3 S1

Problem	Fix
Stringing or fine hairs	Dry HIPS before printing, drop the hotend a few degrees below 240°C, and raise retraction toward 1.2 mm. Damp filament is the No. 1 cause of stringing.
Poor first-layer adhesion	ABS slurry or glue; enclosure needed. Re-level the bed, set a slightly squished first layer, and wipe the sheet with IPA so it is grease-free.
Blobs, zits or rough walls	Slow the outer wall, enable coasting/wipe, and keep retraction near 0.8 mm. Keep the part-cooling fan low so layers bond and warping stays down.

FAQ

What temperature should I print HIPS on the Creality Ender 3 S1?: Start at 240°C for the hotend and 100°C for the bed, then run a temperature tower across 230–255°C to dial in your exact filament brand.
What print speed works for HIPS on this printer?: Around 56 mm/s is a safe starting point on the Creality Ender 3 S1. It can go faster once the profile is tuned, but start conservative for clean walls.
What retraction should I use?: Use about 0.8 mm of retraction (direct drive needs very little). If you see stringing, raise retraction speed before distance and dry the filament.
Do I need an enclosure for HIPS on the Creality Ender 3 S1?: Yes — HIPS needs an enclosure to avoid warping, and the Creality Ender 3 S1 is open, so add one or expect warping and cracking on larger parts.

Sources & how we tuned this

These settings are community-tested starting points, cross-checked against manufacturer guidance and trusted material references:

Last verified: 2026-07-17. Always run a temperature tower and a small calibration print for your exact spool.