Home › Creality Ender 3 V3 SE › PETG-CF

PETG-CF settings for the Creality Ender 3 V3 SE

✓ Great match Advanced Engineering

These are hardware-tuned starting settings for printing PETG-CF on the Creality Ender 3 V3 SE. The Creality Ender 3 V3 SE pairs a direct-drive extruder with a PTFE-lined hotend on an open frame, and tops out at 260°C hotend / 100°C bed. Against PETG-CF's ideal range (240–260°C), that lands us at 240°C nozzle and 80°C bed. Carbon-fibre PETG combines PETG toughness with extra stiffness and demands a hardened nozzle.

Quick answer: 240°C nozzle · 80°C bed · 45 mm/s · 1.5 mm retraction · 40% part fan. Change one setting at a time and validate with a small calibration model.
240°
Hotend
80°
Bed
45
mm/s
40%
Part fan

Recommended PETG-CF profile

Hotend temperature240°C (tower 240–260°C)
Bed temperature80°C
Print speed45 mm/s
Retraction1.5 mm (direct drive)
Part cooling fan40%
Bed adhesionLike PETG; hardened nozzle required.
NozzleHardened steel (this filament is abrasive)
First layer speed16–23 mm/s; same bed temp, verify Z offset
Flow / extrusion multiplierStart at 100%; calibrate flow before touching retraction
DryingStrongly recommended — dry before printing if you hear popping or see inconsistent extrusion
⚠️ PETG-CF can want up to 260°C, but the Creality Ender 3 V3 SE's PTFE-lined hotend caps it near 240°C — going hotter degrades the PTFE tube and releases fumes.
⚠️ Because the Creality Ender 3 V3 SE is not all-metal, keep the hotend at or below 240°C. For the hottest PETG-CF brands you would need an all-metal hotend upgrade.
💡 Best uses for PETG-CF: rigid functional parts, tooling. Estimate the material cost of your next PETG-CF print with the filament cost calculator.

How PETG-CF behaves

StrengthFlexibilityHeatEaseDurabilityDetail

PETG-CF property profile

Strength 82
Flexibility 15
Heat resistance 60
Ease of printing 55
Durability 70

Calibration order

  1. Dry the spool if it shows moisture symptoms, then confirm the nozzle and build plate are clean.
  2. Print a temperature tower inside the 240–260°C range; pick the lowest temperature with strong layer bonding and clean overhangs.
  3. Calibrate flow, then pressure/linear advance if your firmware supports it.
  4. Tune retraction last — more distance is not always better, especially on the direct-drive Creality Ender 3 V3 SE.

PETG-CF brands & what to expect

CF-PETG keeps PETG’s toughness and moisture-sensitivity while adding stiffness and abrasion. Brands vary in fibre load, but all of them require a hardened nozzle and benefit from drying.

🔎 It combines two things that fight you — PETG’s stringing and carbon fibre’s abrasion — so dry the spool AND fit a hardened nozzle. When both are handled, it makes excellent rigid functional parts.

Popular PETG-CF brands: Polymaker, Bambu Lab.

Common PETG-CF problems on the Creality Ender 3 V3 SE

SymptomLikely causeFix
StringingWet filamentDry first; then tune retraction as with plain PETG.
Under-extrusion over timeNozzle wear/clogHardened nozzle; slightly larger diameter.

On the Creality Ender 3 V3 SE specifically: fit a hardened nozzle before running much PETG-CF — the stock brass nozzle wears out fast on abrasive filament.

PETG-CF troubleshootingSymptoms, likely causes and a safe test orderCompare PETG-CF across printersMaterial ranges and every per-printer profile

FAQ

What temperature should I print PETG-CF on the Creality Ender 3 V3 SE?
Start at 240°C for the hotend and 80°C for the bed, then run a temperature tower across 240–250°C to dial in your exact filament brand. Our temperature tower planner builds the tower for you.
What print speed works for PETG-CF on the Creality Ender 3 V3 SE?
Around 45 mm/s is a safe starting point. Check your real speed ceiling with the max volumetric flow calculator.
What retraction should I use for PETG-CF?
Use about 1.5 mm of retraction (direct drive needs very little). If you see stringing with PETG-CF, raise retraction speed before distance and dry the filament first.
Do I need an enclosure for PETG-CF on the Creality Ender 3 V3 SE?
No, PETG-CF prints fine in the open on the Creality Ender 3 V3 SE.
Do I need a hardened nozzle for PETG-CF?
Yes. PETG-CF is abrasive and will wear out a brass nozzle quickly — fit a hardened steel or ruby nozzle before printing much of it.

Reviewed 2026-08-18. See how these starting settings are calculated. Numbers are conservative starting points, not lab measurements.