Home › Voron 2.4 › Silk PLA

Silk PLA settings for the Voron 2.4

✓ Great match Beginner Easy / Everyday

These are hardware-tuned starting settings for printing Silk PLA on the Voron 2.4. The Voron 2.4 pairs a direct-drive extruder with an all-metal hotend inside an enclosed chamber, and tops out at 300°C hotend / 120°C bed. Against Silk PLA's ideal range (205–230°C), that lands us at 215°C nozzle and 55°C bed. Silk PLA prints best slow and slightly hot to keep its glossy metallic sheen.

Quick answer: 215°C nozzle · 55°C bed · 56 mm/s · 0.9 mm retraction · 100% part fan. Change one setting at a time and validate with a small calibration model.
215°
Hotend
55°
Bed
56
mm/s
100%
Part fan

Recommended Silk PLA profile

Hotend temperature215°C (tower 205–230°C)
Bed temperature55°C
Print speed56 mm/s
Retraction0.9 mm (direct drive)
Part cooling fan100%
Bed adhesionEasy; print slower for the best sheen.
NozzleBrass 0.4 mm is fine
First layer speed20–28 mm/s; same bed temp, verify Z offset
Flow / extrusion multiplierStart at 100%; calibrate flow before touching retraction
DryingDry if the spool pops, strings unusually, or the surface looks rough
💡 Best uses for Silk PLA: decorative, vases, gifts. Estimate the material cost of your next Silk PLA print with the filament cost calculator.

How Silk PLA behaves

StrengthFlexibilityHeatEaseDurabilityDetail

Silk PLA property profile

Strength 45
Flexibility 10
Heat resistance 20
Ease of printing 80
Durability 25

Calibration order

  1. Dry the spool if it shows moisture symptoms, then confirm the nozzle and build plate are clean.
  2. Print a temperature tower inside the 205–230°C range; pick the lowest temperature with strong layer bonding and clean overhangs.
  3. Calibrate flow, then pressure/linear advance if your firmware supports it.
  4. Tune retraction last — more distance is not always better, especially on the direct-drive Voron 2.4.

Silk PLA brands & what to expect

Silk PLA relies on additives for its sheen, so brands vary a lot in glossiness and clog tendency. All of them print best slower and slightly hotter than standard PLA to keep the surface shiny.

🔎 Silk PLA is weaker than normal PLA — the additives that create the shine reduce layer adhesion. Use it for looks (vases, display models, gifts), not for functional parts.

Popular Silk PLA brands: SUNLU.

Common Silk PLA problems on the Voron 2.4

SymptomLikely causeFix
Dull or streaky finishPrinting too fast or too coolSlow to ~40 mm/s and add a few degrees of heat.
Colour shifts / bandingInconsistent flow on thin wallsCalibrate flow; avoid ironing which can dull the sheen.

On the Voron 2.4 specifically: it is a fast machine, so if Silk PLA looks rough, drop speed before blaming temperature — many "quality" issues here are really the hotend not keeping up with the flow.

Silk PLA troubleshootingSymptoms, likely causes and a safe test orderCompare Silk PLA across printersMaterial ranges and every per-printer profile

FAQ

What temperature should I print Silk PLA on the Voron 2.4?
Start at 215°C for the hotend and 55°C for the bed, then run a temperature tower across 205–225°C to dial in your exact filament brand. Our temperature tower planner builds the tower for you.
What print speed works for Silk PLA on the Voron 2.4?
Around 56 mm/s is a safe starting point. This printer can go faster once the profile is tuned, but start conservative for clean walls. Check your real speed ceiling with the max volumetric flow calculator.
What retraction should I use for Silk PLA?
Use about 0.9 mm of retraction (direct drive needs very little). If you see stringing with Silk PLA, raise retraction speed before distance and dry the filament first.
Do I need an enclosure for Silk PLA on the Voron 2.4?
No, Silk PLA prints fine in the open on the Voron 2.4.
Do I need a hardened nozzle for Silk PLA?
No. Silk PLA is not abrasive, so the stock brass 0.4 mm nozzle on the Voron 2.4 is fine.

Reviewed 2026-08-18. See how these starting settings are calculated. Numbers are conservative starting points, not lab measurements.