The Voron 2.4 (Voron) has a direct-drive extruder, an all-metal hotend and an enclosed chamber, with a 300°C max hotend and 120°C max bed (350 × 350 × 350 mm). Of 14 common filaments, 14 are a great match on this hardware out of the box.
What filaments does the Voron 2.4 support? The Voron 2.4 supports 14 filaments out of the box. Its all-metal hotend, direct-drive extruder and 120°C bed decide what it can run.
300°
Max hotend
120°
Max bed
14/14
Great matches
Fast
Speed class
Voron 2.4 filament compatibility
| ✅ Great match (print now) | PLA, PLA+, Silk PLA, Wood PLA, PETG, ABS, ASA, Nylon (PA), Polycarbonate, PLA-CF, PETG-CF, TPU, PVA, HIPS |
| ⚠️ Possible with tweaks | none |
| ❌ Not recommended as-is | none |
| Hotend | All-metal — high-temp capable |
| Extruder | Direct drive — good for flexibles |
| Chamber | Enclosed — ABS/ASA friendly |
Every filament on the Voron 2.4: settings table
| Filament | Hotend | Bed | Speed | Retract |
|---|---|---|---|---|
| ✅ PLA | 205°C | 60°C | 84 mm/s | 0.8 mm |
| ✅ PLA+ | 215°C | 60°C | 77 mm/s | 0.8 mm |
| ✅ Silk PLA | 215°C | 55°C | 56 mm/s | 0.9 mm |
| ✅ Wood PLA | 200°C | 55°C | 63 mm/s | 0.8 mm |
| ✅ PETG | 240°C | 80°C | 70 mm/s | 1.5 mm |
| ✅ ABS | 245°C | 100°C | 70 mm/s | 1 mm |
| ✅ ASA | 250°C | 100°C | 63 mm/s | 1 mm |
| ✅ Nylon (PA) | 260°C | 90°C | 56 mm/s | 1.5 mm |
| ✅ Polycarbonate | 275°C | 110°C | 49 mm/s | 1.2 mm |
| ✅ PLA-CF | 215°C | 60°C | 70 mm/s | 0.8 mm |
| ✅ PETG-CF | 250°C | 80°C | 63 mm/s | 1.5 mm |
| ✅ TPU | 225°C | 50°C | 25 mm/s | 1 mm |
| ✅ PVA | 200°C | 60°C | 42 mm/s | 1 mm |
| ✅ HIPS | 235°C | 100°C | 63 mm/s | 1 mm |
✅ great match · ⚠️ possible with tweaks · ❌ not recommended on this hardware.
FAQ
What filaments does the Voron 2.4 support?
Can the Voron 2.4 print PETG?
Yes. PETG prints well on the Voron 2.4 at about 240°C hotend and 80°C bed. See the full Voron 2.4 PETG profile.
Can the Voron 2.4 print ABS or ASA?
Yes — the Voron 2.4 is enclosed, which is exactly what ABS and ASA need to avoid warping.
Does the Voron 2.4 need an all-metal hotend for high-temp filament?
No — the Voron 2.4 already has an all-metal hotend, so it can safely reach the temperatures needed for ABS, ASA, PC and nylon (within its 300°C limit).
Reviewed 2026-08-18.