Home › Creality Ender 3 S1 Pro › PLA+

PLA+ settings for the Creality Ender 3 S1 Pro

✓ Great match Beginner Easy / Everyday

These are hardware-tuned starting settings for printing PLA+ on the Creality Ender 3 S1 Pro. The Creality Ender 3 S1 Pro pairs a direct-drive extruder with an all-metal hotend on an open frame, and tops out at 300°C hotend / 110°C bed. Against PLA+'s ideal range (205–230°C), that lands us at 215°C nozzle and 60°C bed. PLA+ is tougher and less brittle than standard PLA while printing almost as easily.

Quick answer: 215°C nozzle · 60°C bed · 55 mm/s · 0.8 mm retraction · 100% part fan. Change one setting at a time and validate with a small calibration model.
215°
Hotend
60°
Bed
55
mm/s
100%
Part fan

Recommended PLA+ profile

Hotend temperature215°C (tower 205–230°C)
Bed temperature60°C
Print speed55 mm/s
Retraction0.8 mm (direct drive)
Part cooling fan100%
Bed adhesionEasy; slightly higher temp than basic PLA.
NozzleBrass 0.4 mm is fine
First layer speed19–28 mm/s; same bed temp, verify Z offset
Flow / extrusion multiplierStart at 100%; calibrate flow before touching retraction
DryingDry if the spool pops, strings unusually, or the surface looks rough
💡 Best uses for PLA+: functional prototypes, toys, brackets. Estimate the material cost of your next PLA+ print with the filament cost calculator.

How PLA+ behaves

StrengthFlexibilityHeatEaseDurabilityDetail

PLA+ property profile

Strength 65
Flexibility 20
Heat resistance 25
Ease of printing 90
Durability 55

Calibration order

  1. Dry the spool if it shows moisture symptoms, then confirm the nozzle and build plate are clean.
  2. Print a temperature tower inside the 205–230°C range; pick the lowest temperature with strong layer bonding and clean overhangs.
  3. Calibrate flow, then pressure/linear advance if your firmware supports it.
  4. Tune retraction last — more distance is not always better, especially on the direct-drive Creality Ender 3 S1 Pro.

PLA+ brands & what to expect

"PLA+" is a marketing name, not a standard, so eSUN PLA+, SUNLU PLA+ and Polymaker PolyTerra all behave a little differently. Most want 5–15°C more than basic PLA to reach full layer strength. Treat the number on the box as a midpoint and tune from there.

🔎 The point of PLA+ is toughness: it flexes a little before it breaks instead of snapping like brittle PLA, which makes it a better pick for brackets, clips and functional prints that still don’t need heat resistance.

Popular PLA+ brands: eSUN, Polymaker, SUNLU, ELEGOO.

Common PLA+ problems on the Creality Ender 3 S1 Pro

SymptomLikely causeFix
Weak layer bondingPrinted at basic-PLA temperatureRun a temperature tower 5–15°C hotter than your usual PLA.
StringingHigher temp increases oozeKeep retraction tuned; a small temp drop usually clears it.

On the Creality Ender 3 S1 Pro specifically: its direct-drive extruder needs little retraction, so tune retraction to the hardware rather than copying a random online profile.

PLA+ troubleshootingSymptoms, likely causes and a safe test orderCompare PLA+ across printersMaterial ranges and every per-printer profile

FAQ

What temperature should I print PLA+ on the Creality Ender 3 S1 Pro?
Start at 215°C for the hotend and 60°C for the bed, then run a temperature tower across 205–225°C to dial in your exact filament brand. Our temperature tower planner builds the tower for you.
What print speed works for PLA+ on the Creality Ender 3 S1 Pro?
Around 55 mm/s is a safe starting point. Check your real speed ceiling with the max volumetric flow calculator.
What retraction should I use for PLA+?
Use about 0.8 mm of retraction (direct drive needs very little). If you see stringing with PLA+, raise retraction speed before distance and dry the filament first.
Do I need an enclosure for PLA+ on the Creality Ender 3 S1 Pro?
No, PLA+ prints fine in the open on the Creality Ender 3 S1 Pro.
Do I need a hardened nozzle for PLA+?
No. PLA+ is not abrasive, so the stock brass 0.4 mm nozzle on the Creality Ender 3 S1 Pro is fine.

Reviewed 2026-08-18. See how these starting settings are calculated. Numbers are conservative starting points, not lab measurements.