Home › Creality Ender 3 V2 › PETG

PETG settings for the Creality Ender 3 V2

✓ Great match Intermediate Engineering

These are hardware-tuned starting settings for printing PETG on the Creality Ender 3 V2. The Creality Ender 3 V2 pairs a Bowden extruder with a PTFE-lined hotend on an open frame, and tops out at 260°C hotend / 100°C bed. Against PETG's ideal range (230–250°C), that lands us at 240°C nozzle and 80°C bed. PETG is strong and weather-resistant but strings easily, so tune retraction and keep the fan low.

Quick answer: 240°C nozzle · 80°C bed · 50 mm/s · 6 mm retraction · 50% part fan. Change one setting at a time and validate with a small calibration model.
240°
Hotend
80°
Bed
50
mm/s
50%
Part fan

Recommended PETG profile

Hotend temperature240°C (tower 230–250°C)
Bed temperature80°C
Print speed50 mm/s
Retraction6 mm (Bowden)
Part cooling fan50%
Bed adhesionStrong; use glue stick as a release agent, not for grip.
NozzleBrass 0.4 mm is fine
First layer speed18–25 mm/s; same bed temp, verify Z offset
Flow / extrusion multiplierStart at 100%; calibrate flow before touching retraction
DryingStrongly recommended — dry before printing if you hear popping or see inconsistent extrusion
💡 Best uses for PETG: mechanical parts, outdoor parts, bottles. Estimate the material cost of your next PETG print with the filament cost calculator.

How PETG behaves

StrengthFlexibilityHeatEaseDurabilityDetail

PETG property profile

Strength 70
Flexibility 40
Heat resistance 55
Ease of printing 70
Durability 75

Calibration order

  1. Dry the spool if it shows moisture symptoms, then confirm the nozzle and build plate are clean.
  2. Print a temperature tower inside the 230–250°C range; pick the lowest temperature with strong layer bonding and clean overhangs.
  3. Calibrate flow, then pressure/linear advance if your firmware supports it.
  4. Tune retraction last — more distance is not always better, especially on the Bowden Creality Ender 3 V2.

PETG brands & what to expect

PETG is where brand choice starts to matter. Prusament PETG and Overture run clean around 240°C; some budget PETG needs 245–250°C and strings no matter what until it’s dried. Almost every PETG stringing complaint online is really a wet-filament complaint.

🔎 PETG likes to stick to the plate a little too well — use glue stick as a release agent (so it doesn’t rip chunks out of a PEI sheet), and keep the part-cooling fan low so layers actually bond.

Popular PETG brands: eSUN, Overture, Polymaker, Prusament.

Common PETG problems on the Creality Ender 3 V2

SymptomLikely causeFix
Stringing and whiskersMoisture is the #1 cause, then heatDry the spool first, then drop 5°C and raise travel speed.
Ripped-up bed / stuck too hardPETG fuses to bare PEI/glassApply glue stick as a release layer; lower bed 5°C.
Blobs and zits on wallsWet filament + oozing on travelDry, then tune retraction and seam placement.

On the Creality Ender 3 V2 specifically: its Bowden extruder needs more retraction than a direct-drive machine, so tune retraction to the hardware rather than copying a random online profile.

PETG troubleshootingSymptoms, likely causes and a safe test orderCompare PETG across printersMaterial ranges and every per-printer profile

FAQ

What temperature should I print PETG on the Creality Ender 3 V2?
Start at 240°C for the hotend and 80°C for the bed, then run a temperature tower across 230–250°C to dial in your exact filament brand. Our temperature tower planner builds the tower for you.
What print speed works for PETG on the Creality Ender 3 V2?
Around 50 mm/s is a safe starting point. Check your real speed ceiling with the max volumetric flow calculator.
What retraction should I use for PETG?
Use about 6 mm of retraction (Bowden setups need more). If you see stringing with PETG, raise retraction speed before distance and dry the filament first.
Do I need an enclosure for PETG on the Creality Ender 3 V2?
No, PETG prints fine in the open on the Creality Ender 3 V2.
Do I need a hardened nozzle for PETG?
No. PETG is not abrasive, so the stock brass 0.4 mm nozzle on the Creality Ender 3 V2 is fine.

Reviewed 2026-08-18. See how these starting settings are calculated. Numbers are conservative starting points, not lab measurements.